Alteon Application Switch 설정하기 (1) 설정 초기화, 관리 IP 설정
[설정 초기화 작업]
| - 최초 설정시 기존 config 및 software를 초기화한다 명령: /boot/conf/reset 후속 옵션 : factory 후속 옵션 : y 결과확인 : 리부팅 메시지에서 Software version 확인 리부팅 완료 후 /cfg/dump 실행하여 config가 모두 삭제되었는지 확인 |
작업예시
>> Main# /boot/conf factory/reset
Currently set to use active config block on next boot.
Specify new block to use ["active"/"backup"/"factory"]: factory
Next boot will use factory default config block instead of active.
Reset will use software "image1" and the factory default config block.
>> Note that this will RESTART the Spanning Tree,
>> which will likely cause an interruption in network service.
Confirm reset [y/n]: y
Resetting at 11:04:22 Mon Apr 10, 2023...
**** System Reset from boot cli ****
INIT: Sending processes the TERM signal
...
Restarting system.
...
Software Version 27.0.5.0 (FLASH image1), factory default configuration.
...
설정 확인
>> Main# /cfg/dump
script start "Alteon Application Switch 4408" 4 /**** DO NOT EDIT THIS LINE!
/* Configuration dump taken 11:07:30 Mon Apr 10, 2023
/* Configuration last applied at 17:44:38 Wed Mar 13, 2019
/* Configuration last save at 17:44:45 Wed Mar 13, 2019
/* Version 27.0.5, Base MAC address 00:03:b2:9e:a0:40
/
script end /**** DO NOT EDIT THIS LINE!
>> Configuration#
[관리용 IP 설정]
| - IP Interface 1 에 기본 관리 IP를 설정한다 새로 설정한 interface는 enable 해준다 준비한 정보 : ip address 192.168.0.165, subnet mask : 255.255.255.224 broadcast ip : 192.168.0.191, gateway ip : 192.168.0.161 명령 : >> /c/ip/if 1 addr 192.168.0.165 mask 255.255.255.224 broad 192.168.0.191 ena 명령 : >> /c/ip/gw 1 addr 192.168.0.161 ena 설정 확인 후 설정 저장 명령 : >> diff - 기존 config와 변경한 config를 보여준다 명령 : >> apply/save - 새 config를 확정하고, 저장한다 |
작업예시
>> Configuration# /c/ip/if 1
------------------------------------------------------------
[IP Interface 1 Menu]
ip6nd - IP6 Neighbor Discovery Menu
ipver - Set IP version
addr - Set IP address
mask - Set subnet mask/prefix len
vlan - Set VLAN number
relay - Enable/disable BOOTP relay
ena - Enable IP interface
dis - Disable IP interface
del - Delete IP interface
cur - Display current interface configuration
>> IP Interface 1# addr 192.168.0.165
Current IP address: 0.0.0.0
New pending IP address: 192.168.0.165
Pending new subnet mask: 255.255.0.0
>> IP Interface 1# mask 255.255.255.224
Current subnet mask: 0.0.0.0
New pending subnet mask: 255.255.255.224
>> IP Interface 1# broad 192.168.0.191
>> IP Interface 1# ena
Current status: disabled
New status: enabled
>> Configuration# /c/ip/gw 1
------------------------------------------------------------
[Default gateway 1 Menu]
ipver - Set IP version
addr - Set IP address
intr - Set interval between ping attempts
retry - Set number of failed attempts to declare gateway DOWN
vlan - Set VLAN number
prio - Set priority of default gateway route
arp - Enable/disable ARP only health checks
ena - Enable default gateway
dis - Disable default gateway
del - Delete default gateway
cur - Display current default gateway configuration
>> Default gateway 1# addr 192.168.0.161
Current IP address: 0.0.0.0
New pending IP address: 192.168.0.161
>> Default gateway 1# ena
Current status: disabled
New status: enabled
>> Default gateway 1# apply/save
------------------------------------------------------------------
Apply complete; don't forget to 'save' updated configuration.
Request will first copy the FLASH "active" config to "backup",
then overlay FLASH "active" with new config.
Confirm saving to FLASH [y/n]: y
New config successfully saved to FLASH.
>> Default gateway 1#
결과확인
>> Default gateway 1# /c/dump
script start "Alteon Application Switch 4408" 4 /**** DO NOT EDIT THIS LINE!
/* Configuration dump taken 11:14:31 Mon Apr 10, 2023
/* Configuration last applied at 11:14:03 Mon Apr 10, 2023
/* Configuration last save at 11:14:05 Mon Apr 10, 2023
/* Version 27.0.5, Base MAC address 00:03:b2:9e:a0:40
/c/l3/if 1
ena
ipver v4
addr 192.168.0.165
mask 255.255.255.224
broad 192.168.0.191
/c/l3/gw 1
ena
ipver v4
addr 192.168.0.161
/
script end /**** DO NOT EDIT THIS LINE!
>> Configuration#